HD-50 High-Quality Glue Book Binder with Stable Motor and Milling Cutter

Huanda is an authentic Glue Book Binder manufacturer in China. Besides, we can manufacture different types of Glue Book Binder and export them worldwide! Discover extraordinary Glue Book Binder at Huanda!

  • High-quality Motor Work Stable.
  • High-quality Milling Cutter.
ModelHD-50
Binding sizeA3
Speed200 books/hour
Thickness50mm
Power1500W
Ready time30 minutes
Milling cutterSun milling cutter + small milling cutter
Machine size1380*650*1020mm
Pack size1630*770*1120mm
G.W/N.W260/220kg
QTY/PKG1PCS
laminator factory

BASIC OPERATION

1.Start the machine

1.1 Insert the power plug into the AC220V socket.

1.2 Dial the power switch (POWER)to”1″. Then the pilot lamp on the switch is on, the constant temperature pilot lamp gleams and the machine is in the warm-up.

2. Warm-up

2-1 For about 30 minutes,the constant temperature pilot lamp is on and has beep for about 3 seconds. It means that the machine stops warm-up and you can operate.

3. Manual binding

3-1 Dial the choose switch to the manual location (MANUAL). The startup lamp is on.

3-2 According to the thickness of the book and the cover, choose the pressure and time of the clamp (refer to 7. adjustment of the clamping pressure and 8. adjustment of the clamping time).

3-3 Press the key “↓” on setting clamp to loosen the clamp and put into the book. (Attention: Don’t loosen too much. It is better to 3-5mm more than the thickness of the book.) Make the left side align.

3.4 Press the key “↑” on the setting clamp to tightly clamp the book.

3.5 Choose the milling cutter or not. If the lamp of the milling cutter switch is on, the milling cutter is open.

3.6 Press the startup key and the startup lamp goes out. The clamping table goes down and the setting table moves to the left. Through the milling cutter, and stops at the left end of the machine.

3.7 Put the cover on the clamping table, align the left side with the blocking gauge. At this time the startup lamp is on.

3.8 Press the startup key. The startup lamp goes out and the setting table moves to the right. Through the glue trough, stops at the start position. At this time the clamping table rises and starts to clamp.

3.9 When clamping is over, the clamping table will go down. Press the key “↓” on the setting clamp to loosen the clamp and take out the book. The machine returns to the original state.

4. Automatic binding

4-1 At the state of manual binding, adjust the distance between the setting clamps according to the thickness of the book. Generally the distance is 3-5cm thicker than the book.

4-2 Choose the switch to automatic location (Auto).

4-3 Choose the milling cutter or not and set up the pressure and time of the clamp.

4-4 Put the book into the setting table, clear up it well and make the left side align. About 1 second later, the setting clamp begins to clamp the book tightly for about 8 seconds. Then the clamping table goes down and the setting table moves to the left. Through the milling cutter, the setting table finally stops at the left end of the machine.

4-5 Set the cover. About a second later, the setting table returns automatically, through the glue trough, and stops at the original location. The clamping table rises and the clamp begins to work.

4-6 When the clamping time is over, the clamping table goes down and the setting clamp automatically loosens.

4-7 Take out the book, and the machine returns to its original state.

5. Manual pasting

5.1 Dial the clamp switch to the”0″. If the lamp goes out, it is off.

5.2 Refer to manual binding 3-1, 3-3, 3-4, 3-5 3-6.

5.3 For about a second, the setting table moves to the right. Through the glue trough, it stops at the start position. (not clamp)

5.4 Cool the glue for several seconds. Then press the key “↓” on the setting clamp to loosen the clamp and take out the book. The machine returns to the original state.

6. Automatic pasting

6-1 Refer to manual pasting.

6-2 Refer to the automatic binding 4-1, 4-2, 4-3, 4-4.

6-3 Refer to manual pasting5-3.

6-4 When the set clamping time is over (not clamp), the setting clamp automatically loosens.

6.5 Take out the book and the machine resets.

7. Adjustment of the clamping pressure

7-1 The adjustment button for clamping pressure is on the control panel, from 0—100Kg. You can adjust the pressure generally from 60kg to 100kg according to the thickness of the cover. It will be better that the book hasn’t cockles.

7-2 Make sure not to adjust while clamping, or the program will run falsely.

8. Adjustment of the clamping time

8.1 The adjustment button for clamping time is on the control panel, from 0-10 seconds. Generally the time is no less than 2 seconds while using.

8.2 Refer to the data as follow:

Thickness                        Time

Less than1Cm                      4 seconds

Less than 2Cm                     6 seconds

Less than 3Cm                     8 seconds

More than 3Cm                    10 seconds

9. About heat preservation

9-1 For sake of economizing electric energy and preventing the thermosol from ageing for long-term high temperatures, please press the heat-preservation key at working interval. Push the O key, the lamp of heat preservation is on and the machine stops working. The temperature of the glue trough dropped from 150 ℃ to 180 ℃. The constant temperature lamp glimmers. Notice: Before pushing this key, please let the machine reset.

9-2 At Several minutes before working, turn off the lamp of heat preservation by pressing the O key again to stop heat preservation. The temperature of the glue trough rises to 180 ℃ rapidly.  Constant temperature lamp stops glimmering accompanying with about 3 second of beep and the machine resumes to working state.

9-3 For continuous working, you need not use heat preservation.

10. Urgent stop

10-1 If you press the urgent stop key, the machine stops urgently and only glue trough and manual setting clamp board can work.

10-2 When you need to uncover the milling cutter and do some cleaning, please push the urgent stop key first.

10-3 If some urgent thing takes place when the machine is running, please push this urgent stop key rapidly.

10-4 To release the urgent stop, you just need to turn the key for 90°according to the direction of the arrow.

11. Adjustment of the glue quantity on book

11-1 Users can adjust the glue quantity on book by themselves (see the picture 4 of glue trough section). Remove the adjustment key to the arrowhead direction, and the glue quantity reduces; Whereas the glue quantity increases.

11-2 Generally, if the thickness of the book is less than 2cm, adjust the key to the central breaches. If it is more than 2cm, adjust the key to the max. Please do little adjustment according to the situation.

12. Supplement of glue quantity in glue trough

12-1 After the thermosol melting, the glue quantity should between the upper and lower limit. If it is close or lower than the lower limit, more glue should be added into.

12-2 Put the glue into the glue trough directly while adding. Can’t add too much once and make supplement if it is not insufficient after melting.

12-3 Glue quantities can’t exceed the upper limit of mark line, so as not to overflow the glue trough and cause the damage of machine parts.

Get Our Best Quotation
滚动至顶部

Get a Quick Quote!

x

Get a Quick Quote!

x